Dayfile.txt
This Wiki page applies to both Cumulus flavours.
As part of a redevelopment of Wiki, this page has been simplified, by moving some content to new pages. Old links in the support forum, that were to content no longer on this page, will bring you here.
Content previously on this page has been moved as follows:
- Explanations about Cumulus terminology can be accessed from Category:Terminology page
- Each line in this file represents one day, but the start time need not be same for all fields,
- so please see Meteorological day, and today.ini for more details about that
- Advice regarding editing this file has been moved to Amending dayfile page, this also covers date-separator issues and dealing with missing or corrupted lines
- General advice about Cumulus files with a .txt extension has been consolidated on Category:Files_with_Comma_Separated_Values page
- Advice about correcting any rogue extreme figures inadvertently stored in this file has been consolidated in new Correcting Extremes page
- If some lines in your file have fewer fields than other lines the advice has been consolidated on Calculate Missing Values page
- For MX there is a Create Missing Utility, which checks spot readings in the MMMyylog.txt files, adds any missing derivative spots (e.g. heat index) and uses these figures to recalculate daily derivatives and uses those to replace missing fields/lines in dayfile.txt
- For the legacy Cumulus, there was a dayfile editor with create missing option, that performed equivalent function
- If you import historic data from before you started using Cumulus into Standard log files,
- then see Calculate Missing Values page for how to generate new lines in dayfile.txt
- Cumulus MX is more fussy, than Cumulus 1, about various formattting issues, see below, also see Migrating_from_Cumulus_1_to_MX#dayfile.txt section for more advice
The content that remains on this page is summarised by the table of contents that follows.
About this file
- This Wiki page describes one of the files not included in any release download.
- This daily summary file (Steve Loft shortened that to "day" plus "file") uses a ".txt" extension, and is essentially a plain text file in CSV format.
- The file is created in data sub-folder of your Cumulus installation when Cumulus needs to store its first line in this file.
- Cumulus MX reads the whole of this file when you restart the software,
- So if you move house, it is probably best to archive the old "dayfile.txt", and avoid any discontinuities in any graphs plotted from active file
(speciallog.txt is another log file that contains all dates in a single file, as do all the .ini files).
How Cumulus Creates and Updates this file
- Cumulus reads values supplied by your weather station, (either directly while Cumulus running, or for some weather station types can read historic data during catch-up on restarting Cumulus)
- Cumulus converts them to the units you prefer,
- Cumulus applies any calibration (multiplier and offset) you have set,
- For a sub-set of those readings (perhaps those every minute if readings are collected every 10 seconds), the spot values of source items like temperature, humidity, wind speed, can be used in calculations of derived items like "wind chill", "dewpoint" and "feel-like" temperature.
- Cumulus then sees if the resulting soource, or derived, value implies any extreme records file needs to be updated
- Daily extremes are held in today.ini and that is main source used when a new line is added to "dayfile.txt"
Why this file should be backed up
- This file contains daily extremes, the accuracy of those daily extremes depends on the interval between the spot readings that are used as explained above.
- If the file is corrupted, and not regenerated from a back-up, the only source of spot readings is the MMMyylog.txt files, and their interval might be only every half an hour (it has to be an exact fraction of an hour).
- As explained here minima and maxima between such logging intervals are not recorded by Cumulus software
- Thus it is worth backing up this file, to another device than that running Cumulus, on a regular basis, probably a few times a week, to ensure this precious data is not lost if your device running Cumulus has a malfunction (or is damaged), or an electrical blip (or mistake by you) causes corruption to the original file,
Cumulus does periodically copy this file within the installation, but the copies are only kept for a limited time, and are on the same physical storage device, and so your main file is corrupted you might not be able to access the Cumulus back up or might not be able to go far back enough for an uncorrupted file:
- The file is backed up when MX is restarted into a date/time stamped sub-folder of the backup folder
- The file is also backed up (to a date/time stamped sub-folder within daily sub-folder of that backup sub-folder) during the end of day process, depending on the release you are running the back-up copy may, or may not, include the line that is appended in the same end of day
Retention of these back ups:
MX only keeps the last 9 of the date/time stamped subfolders.
Legacy Cumulus 1 only keeps up to 8 of the date/time stamped subfolders.
Specific issues for MX
WARNING: It is important to note that some releases of MX are very fussy about consistency in all lines of dayfile.txt. Earlier releases tended to have better compatibility with the legacy software. Subsequent releases expected every line to be expressed exactly as specified in the locale. MX in its latest release is trying to cope better with inconsistent date separators, and at the time of writing this there was a proposal for forcing this file to use decimal points (full stops not commas) regardless of locale. Therefore, information here might be incorrect for the release that you are using.
Date field: Cumulus 1 (C1) did not care what character (or characters) separated the day, month, and year elements of the date field. MX insists that the same character (or characters), as defined in the locale, is used for all lines in file.
Real number fields: MX uses the locale to decide what character (decimal comma or decimal point) separates integer and decimal parts of numbers. Every line of the file must be consistent in use of integer/decimal separator. C1 used the Region settings in Microsoft's Control Panel to determine how to store (and output) numbers for you, but (except if list separation character was comma) was fairly tolerant when reading old data in files.
Time-stamp fields: MX insists on HH:mm format being consistently used in every line of file, C1 did not care what (non-space, non-field separator) symbol separated the minutes from the hours.
Number of fields: The number of fields in the file increases in various versions as shown in #List_of_fields.
- C1 will accept (as did Cumulus 2) any line with 15 to 45 fields in it. This is because the earliest version only stored 15 fields, as C1 was developed fields were added (as shown in field list) until there were 45 fields.
- MX too has added fields as the software has developed, and it even (as shown in field list) inadvertently added 2 fields later removed. The difference is that MX (for some functionality from release 3.4.5, for all functionality from release 3.9.5) reads the whole file into an array with a fixed number of elements, therefore every line ends up with same number of fields when written back into file. If you have some lines in your file that were created by an earlier release of Cumulus, and so have less than whatever is the current number of fields for the release you are using, you can add the missing derived fields, please see Calculate Missing Values page. Please ensure you use the right version of the "Create Missing" utility mentioned on that page as it also get upgraded when fields are added.
How to view or edit this file
An editor has been included within Cumulus:
- From release 3.4.5 (13 Mar 2020) onwards: In the interface go to Data logs menu and select Dayfile
- From version 1.9.2 (5th October 2011) to final legacy release: On Main Screen from Edit menu select Dayfile.txt
- Note for obsolete version 1.9.0 to 1.9.3: There is a bug in these versions in that 'Create missing' inserts 'heating and cooling degree day' values the wrong way round.
- Note for obsolete version 1.9.3 only: Create missing might in some cases be affected by a bug in 1.9.3 that can cause lines to be stored in incorrect date order (dayfile.txt uses dd.mm.yy, dd/mm/yy or dd-mm-yy, for its date field; and all lines should be in ascending chronological order)
- There are no known bugs for dayfile.txt handling in version 1.9.4 builds 1086 to 1101. Build 1099 is the standard stable final release of Cumulus 1 for most weather station types, 1100 and 1101 are for specific weather station types.
For detailed information, please see viewing/editing dayfile.txt.
Reading the file
See Daily Summary page for a full discussion of ways, external to Cumulus, to read this file.
Apart from the viewing/editing options just described, Cumulus software reads this daily summary file in various other circumstances depending on the release you are running.
- The legacy Cumulus has a number of screens for viewing data for various periods, these use several of the for their source, including "dayfile.txt". The Select a graph feature also uses several of the for their source, including "dayfile.txt". Thus the legacy software only reads the file when the Cumulus user makes a specific request, in normal operation the existing content is ignored, and the end of day action uses a simple "append" instruction.
- From release 3.9.2 - b3097 (7 Dec 2020), MX reads the entire dayfile.txt file, to drive the historic charts functionality; both in the interface, and the example included Historic Charts web page.
- Consequently, any error in say the date field (or change of separating character) will stop historic charts working.
List of fields in dayfile.txt
For your installed build please see dayfileheader.txt (stored within the folder that contains your Cumulus executable), as that will list which fields your Cumulus installation uses.
If you have been using Cumulus for a while, you may wonder which of your log file lines might be shorter, so the table below shows fields grouped by the Cumulus version when those fields were added.
Field numbering
Please note the list of fields has been rewritten especially for MX. As part of the rewrite, the fields have been renumbered, in some forum posts you might see references to old numbering, in others to new numbering.
- The original table below was for Cumulus 1 and then field number was starting from zero.
- Cumulus 1 does not actually number lines, however it does count lines as it reads them, so if there is an error when it reads the file, the original Cumulus will report the line number where it first found an error (this uniquely identifies the line even if a date is duplicated or a line feed has been deleted so two lines are merged).
- Please note that the editor in Cumulus 1 allows you to change the date, as well as all the other fields, although the lines must be kept in ascending date order to avoid errors when subsequently reading the file
- The fields are now numbered starting from 1 to fit in with Cumulus MX where when the log file is read, the processing code adds a line number in front of the date field on each line it holds.
- The Cumulus MX user may not be aware of this happening as it is within the internal workings, where data from the file is transferred to an array, or data from the array is written back into the file.
- By using line numbers, MX is able to identify which line has been deleted or edited, MX coding treats the date as a fixed bit of text (MX does not allow you to change a date)
The old numbering from zero had two advantages:
- It stressed that the date field was different to the rest, all other fields were either values or time-stamps
- Numbering starting from zero is consistent with standard indexing used for arrays in programming languages (like JavaScript), so the number shown was the number to quote in any scripts where a Cumulus 1 line was converted to an array, and you needed to address a single field.
Information shown in the table
- The date must be a unique identifier, the same date should not be repeated in another line, however Cumulus 1's editor allows you to change that date field.
- The remaining fields were all either numerical values, or a time paired with (except for first wind field) preceding numerical value.
- Cumulus 1 actually enforces this pairing (i.e. it validates that a time is present where it is needed).
- The alphabetic column identifiers used by many spreadsheets are shown
- IMPORTANT: Ensure all columns are set to "text" format,
- Note that you will corrupt this file if you let your spreadsheet recognise content as dates or time, change the number of decimal places.
- The type of field is shown in the table,
- you must not include a sign for an unsigned field,
- you can not specify a decimal point in an integer field,
- all time fields must use 5 character "HH:mm" format
- The field description is shown, together with references to where that terminology is explained
Table listing Fields
| Field number | Spreadsheet column | Field type | Description |
|---|---|---|---|
| 0 | For internal MX purposes, the zero field identifies a field that holds the line number. It is not actually stored as a field in the log file, but precedes any line exchanged via an application programming interface, and therefore is also included in an array representing all the fields in any log file line.
If you are processing this log file using a third party (or your own) script, that probably does not place the line number into any array, and your array elements will start at 0 for the field labelled 1 in this table, so putting all field numbers out by 1. | ||
| Those fields included below have been in dayfile.txt from the start of Cumulus 1 (Version 1.0, the First release on 27th January 2004). | |||
| 1 | A | 8 characters | Date as 2 figure day [separator] 2 figure month [separator] 2 figure year - the separator is that set in the windows system short date format (see setup) |
| 2 | B | Unsigned number | Highest wind gust speed |
| 3 | C | unsigned integer | Bearing of highest wind gust |
| 4 | D | 5 characters | Time of highest wind gust |
| 5 | E | signed decimal | Minimum temperature |
| 6 | F | 5 characters | Time of minimum temperature |
| 7 | G | signed decimal | Maximum temperature |
| Consistency Note: In some cases Minimum comes before Maximum, in other cases Maximum is before Mimum | |||
| 8 | H | 5 characters | Time of maximum temperature |
| 9 | I | Unsigned number | Minimum sea level pressure |
| 10 | J | 5 characters | Time of minimum pressure |
| 11 | K | Unsigned number | Maximum sea level pressure |
| 12 | L | 5 characters | Time of maximum pressure |
| 13 | M | unsigned number | Maximum rainfall rate |
| 14 | N | 5 characters | Time of maximum rainfall rate |
| 15 | O | unsigned number | Total rainfall for the day |
| Above here represents the minimum length for every line, a count of 15 items | |||
| [There is no record of which version added this next field. The Cumulus Support Forum, while it was hosted by Steve Loft, moved to new forum software (phpBBB3) on 2 Jun 2008, and started afresh without retaining any previous content. Therefore all announcements about the content of each build prior to version 1.7.9 were lost. All that can be deduced is that it was between versions 1.2.5 and 1.5.1 as these do not appear in the release history issued by Steve Loft. The first mention of it in the new forum was not until December 2008, but that was not about when it was released. A web tag for this variable was added in Build 978 of 1.9.1 beta, which was obviously long after it was first calculated.
Because of that, in "DataEditor.cs" (part of the source code that is compiled into CumulusMX.exe) this addition has "Extended for ???" as a comment] | |||
| 16 | P | signed decimal | Average temperature for the day |
| (Wind run was added from version 1.8.4) | |||
| 17 | Q | unsigned number | Daily wind run |
| (The next pair of entries were added from version 1.8.9 build 907 (June 2010) as part of a total redesign of how dayfile.txt was implemented in Cumulus 1) | |||
| 18 | R | unsigned number | Highest Average Wind Speed |
| 19 | S | 5 characters | Time of Highest Avg. Wind speed |
| (The two pairs of humidity entries were added in October 2010, a v 1.9.0 beta, the exact build number is now lost) | |||
| 20 | T | unsigned integer | Lowest humidity |
| 21 | U | 5 characters | Time of lowest humidity |
| 22 | V | unsigned integer | Highest humidity |
| 23 | W | 5 characters | Time of highest humidity |
| (The next two entries were added from version 1.9.0) | |||
| 24 | X | (not documented) | Total evapotranspiration (Only valid for Davis stations, shows zero otherwise) |
| 25 | Y | unsigned | Total hours of sunshine (only valid if sunshine sensor connected)
Important if rollover time is 9 am or 10 am: Most fields in this file are updated taking information from today.ini. For a non-midnight rollover, then the Sunshine hours reported here is from 00:01 on the calendar date corresponding to the date in the first field of this file, to subsequent midnight, and that end time is 9 or 10 hours before when this file is updated. Meanwhile, the sunshine hours count has been reset and so the figure in today.ini is not what is wanted here. For that reason the sunshine hours reported here are taken from yesterday.ini. |
| (The next 16 entries were added from version 1.9.1 May 2011) | |||
| 26 | Z | signed decimal | High Heat index (added to Cumulus in 1.7.11 only as spot value, not stored) |
| 27 | AA | 5 characters | Time of high heat index |
| 28 | AB | Signed decimal | High Apparent temperature |
| 29 | AC | 5 characters | Time of high apparent temperature |
| 30 | AD | signed decimal | Low apparent temperature |
| 31 | AE | 5 characters | Time of low apparent temperature |
| 32 | AF | unsigned number | High hourly rain |
| 33 | AG | 5 characters | Time of high hourly rain |
| 34 | AH) | signed decimal | Greatest wind chill (high wind speed, low temperature) (calculated since version 1.8.3 as spot value, not stored) |
| 35 | AI | 5 characters | Time of greatest wind chill |
| (The next two pairs for dew point were added in version 1.9.2 beta build) | |||
| 36 | AJ | signed decimal | High dew point |
| 37 | AK | 5 characters | Time of high dew point |
| 38 | AL | signed decimal | Low dew point |
| 39 | AM) | 5 characters | Time of low dew point |
| (The next three entries were added in version 1.9.2 Build 1004) | |||
| 40 | AN | unsigned integer | Today's dominant/average wind direction |
| 41 | AO | unsigned decimal | Heating degree days |
| 42 | AP | unsigned decimal | Cooling degree days |
| The next two pairs were added in legacy version 1.9.3 build 1036 (these only show valid values if appropriate sensors exist).
Fields listed up to those following here applied to the final legacy Cumulus 1.9.4 and formed the basis for early releases of Cumulus MX. | |||
| 43 | AQ | unsigned decimal | High solar radiation |
| 44 | AR | 5 characters | Time of high solar radiation |
| 45 | AS | unsigned decimal | High UV Index |
| 46 | AT | 5 characters | Time of high UV Index |
| The next two pairs were added in MX release 3.6.0, 2 more derived values and their times | |||
| 47 | AU | signed decimal | High Feels Like temperature |
| 48 | AV | 5 characters | Time of high feels like temperature |
| 49 | AW | signed decimal | Low Feels Like temperature |
| 50 | AX | 5 characters | Time of low feels like temperature |
The next two pairs were added in release 3.6.12
| |||
| 51 | AY | signed decimal | High Canadian Humidity Index or Humidex |
| 52 | AZ | 5 characters | Time of high Humidex
Bug for releases 3.13.0 to 3.14.2 inclusive: The major code rewrite for release 3.13.0 replaced the previous code for the processing for all Cumulus files, the new code incorrectly stored Time of high feels like temperature in this field for all these releases! Corrected in minor code rewrite for 3.14.3 - b3163 25 Jan 2022 (not released to public until 3.15.0 - b3169 Released 31 Jan 2022) |
| Just confirming that the next 2 fields were included by mistake in an emergency release (3.6.12), and are not included in any other version, so have labelled them as error. | |||
| 53 (error) | BA | signed decimal | Labelled as Low Humidex, but not used, (appear in 3.6.12, but no other release) |
| 54 (error) | BB | 5 characters | Labelled as Time of low Humidex, but not used, (appear in 3.6.12, but no other release) |
| The next value was added in release 3.12.0 | |||
| 53 (new) | BA | unsigned decimal | Cumulative Chill Hours since start of season |
| The next value and time fields were added in release 3.20.0 | |||
| 54 | BB | unsigned decimal | Highest rainfall total in (an approximate, as it depends upon timing of earlier entries in Recent history) 24 hour period ending in Meteorological day |
| 55 | BC | 5 characters | Time when (approximate) 24 hour period for rainfall total above ends |
Example of the file
An extract of a few lines of a dayfile.txt
01/08/11,19.3,61,10:22,12.5,06:58,23.8,14:49,1014.26,20:46,1018.83,09:28,0.0,00:00,0.0,17.8,21.6,4.6,10:44,36,14:14,86,01:56,3.56,8.9,23.8,14:49,23.1,14:50,12.3,06:59,0.0,00:00,12.5,06:58,11.3,00:16,6.9,14:34,354,2.0,1.5 02/08/11,16.1,20,16:55,14.7,06:45,24.2,13:54,1013.79,19:13,1015.65,11:14,0.0,00:00,0.0,18.9,13.7,8.0,15:55,42,20:42,85,06:50,2.79,4.9,24.2,13:54,24.3,13:55,15.1,06:40,0.0,00:00,14.7,06:45,14.8,11:59,7.0,21:09,57,1.0,1.7 03/08/11,14.5,36,17:23,14.9,05:50,24.6,14:46,1012.70,18:44,1015.99,08:34,0.0,00:00,0.0,19.4,17.2,4.8,16:04,50,14:38,79,07:04,3.05,5.8,24.6,14:46,25.4,14:47,15.0,05:50,0.0,00:00,14.9,05:50,14.2,20:01,8.9,00:16,32,0.8,1.9 04/08/11,17.7,16,15:43,14.1,06:20,25.3,15:06,1013.08,18:42,1015.31,08:28,0.0,00:00,0.0,20.2,19.4,8.1,14:12,52,18:20,92,06:55,3.30,9.1,25.3,15:06,26.8,14:55,14.9,06:20,0.0,00:00,14.1,06:20,15.8,14:55,12.5,06:25,36,1.0,2.9 05/08/11,16.1,32,12:52,14.2,06:12,22.2,14:07,1013.89,00:01,1016.36,09:43,0.0,00:00,0.0,18.6,21.6,5.2,13:00,62,15:57,87,06:11,3.30,8.4,22.2,14:07,23.5,14:10,14.8,07:19,0.0,00:00,14.2,06:12,15.4,10:33,12.0,06:03,34,0.9,1.3 06/08/11,16.1,309,11:15,14.3,05:29,22.4,17:12,1014.46,20:02,1016.97,10:38,0.0,00:00,0.0,18.4,19.2,5.5,16:21,55,13:33,92,05:20,2.79,7.9,22.4,17:12,23.3,18:17,15.1,06:09,0.0,00:00,14.3,05:29,14.2,18:12,10.9,10:38,32,1.1,1.3 07/08/11,17.7,342,13:24,12.9,05:47,24.1,14:53,1013.92,19:49,1016.43,09:36,0.0,00:00,0.0,18.4,19.1,6.3,14:06,48,12:45,89,05:36,3.30,9.0,24.1,14:53,24.6,15:48,13.3,05:47,0.0,00:00,12.9,05:47,14.6,15:52,10.7,11:33,11,1.6,1.7
