Pressure Measurement: Difference between revisions
m (→Units: added dates) |
m (→Setting the Datum: Remove description of setting sea level pressure in cumulus, replace with setting in weather station) |
||
| Line 15: | Line 15: | ||
==Setting the Datum== |
==Setting the Datum== |
||
All weather stations allow you to adjust the pressure for sea level. You should not make the adjustment within Cumulus. |
|||
In Cumulus, the pressure datum is set by going to Configuration/Calibration and entering a number into the Pressure slot in Offsets. |
|||
For Fine Offset see [[FAQ#Cumulus_doesn.E2.80.99t_show_the_same_pressure_as_my_Fine_Offset_console]]. |
|||
The best way to get MSL pressure at your location is to go to a site like [http://www.wunderground.com/ Weather Underground] and enter your location. It will find a weather station nearby and give you the current MSL pressure. It's a good idea to choose an airport site because you can be sure that it has been accurately reduced to MSL pressure. |
The best way to get MSL pressure at your location is to go to a site like [http://www.wunderground.com/ Weather Underground] and enter your location. It will find a weather station nearby and give you the current MSL pressure. It's a good idea to choose an airport site because you can be sure that it has been accurately reduced to MSL pressure. |
||
Alternatively, look at a isobar chart at a site like [http://www.meteorologica.info/UKisobars.htm weather superstore], and interpolate for your location. |
|||
On the other hand, most airport sites only give pressure to the nearest hPa, so you can be 0.5 hPa out if you use that, whereas most personal weather stations give pressure with 0.1 hPa precision. |
|||
The best time to set your datum is when the pressure is |
The best time to set your datum is when the pressure is not changing either with time or between nearby locations. Note most sites only give pressure to the nearest hPa, so you can be 0.5 hPa out if you use that, whereas most personal weather stations give pressure with 0.1 hPa precision. |
||
== Calibration == |
|||
To figure out what to put into the Cumulus box, use the following equation, where <math>P_c</math> is the pressure on your console and <math>P_s</math> is the pressure from a nearby station: |
|||
If you find that your sensor is inaccurate, it may be possible to apply a calibration within cumulus (configuration menu). |
|||
<math>Correction = P_s - P_c</math> |
|||
==Locating the Barometer== |
==Locating the Barometer== |
||
Revision as of 09:07, 7 September 2013
Atmospheric pressure (also known as barometric pressure) is the pressure exerted by the weight of the air above the Earth's surface. It is measured using a barometer. Atmospheric pressure and its rate of change are important parameters for weather and the ocean.
Units
The units used for pressure are hPa (hecto Pascals, although not a System International unit because of its prefix, this is used by meterorologists in much of the world).
Alternatives units are mb (millibars, this is the equivalent used for public communications, but its scientific definition has varied from 101,325 Pa to (from 1982) 100,000 Pa), mmHg (millimetres of mercury, strictly a function of temperature and gravitational force as well as atmospheric pressure, abandoned in 1929), torr (now defined as exactly 1/760 of a standard atmosphere, almost equivalent to mmHg, but mmHg varies by temperature and gravitational strength), kPa (kiloPascals is a SI unit, used in Canada), inHg (inches of mercury, used in USA and by some UK instruments, but strictly a function of temperature and gravitational force as well as atmospheric pressure) are alternatives.
Cumulus supports:
- 0 = mb (millibars)
- 1 = hPa (hectoPascals)
- 2 = in (inches of mercury)
Datum
Pressure decreases exponentially with altitude, so for consistency it is reduced to the common datum of mean sea level (MSL).
Setting the Datum
All weather stations allow you to adjust the pressure for sea level. You should not make the adjustment within Cumulus. For Fine Offset see FAQ#Cumulus_doesn.E2.80.99t_show_the_same_pressure_as_my_Fine_Offset_console.
The best way to get MSL pressure at your location is to go to a site like Weather Underground and enter your location. It will find a weather station nearby and give you the current MSL pressure. It's a good idea to choose an airport site because you can be sure that it has been accurately reduced to MSL pressure.
Alternatively, look at a isobar chart at a site like weather superstore, and interpolate for your location.
The best time to set your datum is when the pressure is not changing either with time or between nearby locations. Note most sites only give pressure to the nearest hPa, so you can be 0.5 hPa out if you use that, whereas most personal weather stations give pressure with 0.1 hPa precision.
Calibration
If you find that your sensor is inaccurate, it may be possible to apply a calibration within cumulus (configuration menu).
Locating the Barometer
For most personal weather stations, the barometer is in the console, usually attached to the printed circuit board. These barometers are very cheap devices that simply record the load on a diaphragm. Unlike the barometer in an automatic weather station, they have no temperature compensation. Therefore, for best pressure readings, you should locate the console in a place where the temperature is reasonably constant, not in direct sunlight or near a heater.
How Accurate are PWS Barometers?
The figure below shows a comparison between the pressure measured by a Fine Offset PWS and a nearby AWS. You can see that the comparison is excellent.
